Custom EVA Hard Case Manufacturer in Dongguan, China

We are an EVA hard case factory in Shijie Town, Dongguan: 10+ years of compression moulding, 120+ staff, 150,000 pcs of monthly capacity and a library of 300+ existing moulds. Mould drawing, pressing, stitching, lining and packing all happen in one building, so a project never waits on a third party. MOQ is 300 pcs per style.

Factory capability

From mould drawing to sealed carton in one plant

A moulded shell begins as a flat sheet: 5 mm EVA foam laminated to 1680D nylon, 600D polyester or PU leather, cut to a flat pattern, then pressed over an aluminium mould until it holds the tool shape. The shell stays rigid after cooling, so the case carries a device instead of resting on it. We draw and cut every mould in our own tool room.

A sewn nylon case is a bag with a soft wall: it folds, it sags, and it passes impact straight to the contents. A moulded EVA shell is a rigid 5 mm wall with a controlled radius at every corner, so a 1.2 m drop on six faces spreads the load across the whole panel. That is why drone, VR and medical buyers specify moulded shells and ask for ISTA 3A test reports.

  • 300+ moulds on file: 7–10 days sampling on a stock mould
  • 150,000 pcs per month with 120+ staff in one plant
  • 5 mm EVA, 75D, faced in 1680D nylon or 600D polyester
  • 20–30 days bulk production after sample approval
Send Your Design
Compression moulding press forming a 5 mm EVA hard case shell
What decides the result

Shell, insert, finish, in that order

Three decisions fix cost and protection before a case is pressed. Change one later and the tooling changes with it.

The shell

Wall thickness, corner radius and face fabric decide how much impact a case absorbs. We press 5 mm EVA from 75D foam, faced in 1680D, 600D or PU.

The insert

Die-cut foam holds the device; a loose insert lets it move. We cut EVA or PU to the product outline and test-fit your sample before finishing.

The finish

Zipper, lining, handle and logo decide how a case reads on a shelf. We fit YKK or waterproof zippers, velvet or jersey lining and webbing handles.

Quality

How a moulded case is checked before it ships

The first shell out of a new mould is a first article, not a production unit. We measure wall thickness at nine points, check the zipper gap around the full perimeter, and drop the case at 1.2 m on six faces with a weighted dummy inside. If one corner deforms, the mould is re-cut before the run starts. The same check runs again on every reorder.

Bulk runs carry three checks: an inline inspection every 50 pcs, a full measurement pass against the approved spec, and an AQL 2.5 final inspection with photos of the carton, the label and the shell surface. Zippers are cycle-tested to 5,000 open-and-close cycles. You receive the report, the measurement sheet, the defect log and retained samples before the balance is due.

  • First-article check on every new mould: 9 wall-thickness points
  • 1.2 m drop test on six faces with a weighted load inside
  • 5,000-cycle zipper test on every zipper batch received
  • AQL 2.5 final inspection with a photo report per carton
Ask for a test report
Inspector checking the zipper seam and shell surface of a moulded EVA case
Projects

Moulded cases built on our own moulds

Four formats that run through the plant monthly. Each can be re-pressed in another face fabric, lining and insert at 300 pcs.

Process

Five steps from a drawing to sealed cartons

Most projects run 7–10 days to sample and 20–30 days to bulk. A new mould moves the sampling date, not the production window.

01

Send the drawing or the device

A 3D file, a sketch or the physical product works. Tell us the drop standard and the target retail price and we will say whether a 5 mm shell is the right wall.

02

Mould match or mould cut

We check your product against 300+ existing moulds first. If one fits, sampling takes 7–10 days; a new mould takes 15–20 days including the first article.

03

Approve the sample

You receive a finished case with the final lining, zipper and insert, a measurement sheet, a photo set from six angles and any deviation noted in writing.

04

Bulk moulding and assembly

20–30 days after approval: moulding, trimming, lining, zipper fitting, insert assembly and packing, with an inline inspection every 50 pcs and a daily output report.

05

Inspect, mark and ship

AQL 2.5 final inspection and a photo report, then cartons marked to your instruction, a packing list signed off and loading FOB Shenzhen or Yantian, CIF or DDP.

Specs

Moulded case specification range

The range we press most often. Anything outside it is a tooling conversation, not a refusal.

Material
5 mm EVA foam, 75D, laminated to 1680D nylon, 600D polyester or PU leather
Shell
Compression moulded, radiused corners, 1.2 m drop tested on six faces
Lining
Velvet, jersey or plain EVA; die-cut EVA or PU insert
Zipper
YKK nylon coil, waterproof or #5 metal, 5,000-cycle tested
Insert
Die-cut to the product outline, pick-and-pluck or removable tray
Logo
Embossed, heat transfer, metal plate, rubber patch or silk screen
MOQ
300 pcs per style, 100 pcs per colour on stock moulds
Lead time
7–10 days sampling on stock moulds; 20–30 days bulk
Pricing

Indicative case pricing

FOB Shenzhen at 1,000 pcs unless stated: 5 mm shell, 1680D face, velvet lining and a die-cut insert. Tooling is quoted separately and credited on 2,000+ pcs.

Small cases

US$2.60 / pc

Watch, jewellery and thermometer formats, FOB at 1,000 pcs.

  • 300 pcs MOQ
  • Stock mould from the 300+ library
  • Velvet lining and die-cut insert
  • Embossed or heat transfer logo

Large cases

US$9.80 / pc

Drone fly-more, VR headset and keyboard formats, FOB at 2,000 pcs.

  • 2,000 pcs per style
  • 5 mm shell with a second laminated layer
  • Shoulder strap and D-ring
  • ISTA 3A test report on request

Questions buyers ask first

How is a moulded EVA case different from a sewn nylon case?
A sewn case is a soft bag: it folds and passes impact to the device. A moulded 5 mm EVA shell holds a radiused shape and spreads a 1.2 m drop across the whole panel.
How many pieces do I have to order?
300 pcs per style, or 100 pcs per colour when the mould comes from our 300+ library. Mixed sizes count toward the same minimum.
How long does sampling and production take?
Sampling is 7–10 days on a stock mould, 15–20 days with a new one. Bulk production runs 20–30 days after sample approval, then freight.
What does a new mould cost?
US$600–1,400 as a one-off, depending on case size and insert count. It is credited against orders of 2,000 pcs or more and stays on file for reorders.
What are your payment and trade terms?
30% deposit on order confirmation and 70% before shipment, against the inspection report. We quote FOB Shenzhen or Yantian, CIF and DDP.

Send one drawing, get one honest cost

Tell us the device, drop standard and quantity. We will say whether a stock mould fits or a new one is needed, and price both.